A Review on Optimization of Cutting Parameters on Turning
 |
International Journal of Engineering Trends and Technology (IJETT) | 
|
| © 2015 by IJETT Journal | ||
| Volume-28 Number-2 |
||
| Year of Publication : 2015 | ||
| Authors : Dharindom Sonowal, Thuleswar Nath, Dhrupad Sarma |
||
| DOI : 10.14445/22315381/IJETT-V28P211 |
Citation
Dharindom Sonowal, Thuleswar Nath, Dhrupad Sarma"A Review on Optimization of Cutting Parameters on Turning", International Journal of Engineering Trends and Technology (IJETT), V28(2),54-60 October 2015. ISSN:2231-5381. www.ijettjournal.org. published by seventh sense research group
Abstract
The purpose of this paper is to make an
attempt to review the literature on optimization of
cutting parameters for minimum surface roughness in
turning. The cutting parameters like spindle speed
(rpm), feed (mm/rev) and depth of cut (mm) are taken
into consideration.
References
[1] S. Thamizhmanii, S. Saparudin and S. Hasan, ?Analyses of
Surface Roughness by Turning Process using Taguchi
Method, Journal of Achievements in Materials and
Manufacturing Engineering, Volume 20, pp. 503 – 506,
January-February 2007.
[2] C. Natarajan, S. Muthu and P. Karuppuswamy,
?Investigation of Cutting Parameters of Surface Roughness
for a Non-Ferrous Material using Artificial Neural Network
in CNC turning Journal of Mechanical Engineering
Research, Vol. 3, pp. 1-14, January 2011.
[3] V. Suresh Babu, S. Sriram Kumar, R. V. Murali and M.
Madhava Rao, ?Investigation and validation of optimal
cutting parameters for least surface roughness in EN24 with
response surface method, International Journal of
Engineering, Science and Technology, Vol. 3, pp. 146 – 160,
November 2011.
[4] Sahoo, P., ?Optimization of Turning Parameters for Surface
Roughness using RSM AND GA, Advances in Production
Engineering & Management, Volume 6, pp. 197 – 208,
2011.
[5] C. R. Barik and N.K. Mandal, ?Parametric effect and
Optimization of Surface Roughness of EN31 in CNC dry
Turning, International Journal of Lean Thinking, Vol. 3, pp.
54 – 66, December 2012.
[6] Rahul Davis and Mohamed Alazhari, ?Optimization of
Cutting Parameters in Dry Turning Operation of Mild Steel,
International Journal of Advanced Research in Engineering
and Technology, Volume 3, pp. 104-110, July-December
2012.
[7] K. Adarsh Kumar, Ch. Ratnam, B.S.N. Murthy, B. Satish
Ben and K. Raghu Ram Mohan Reddy, ?Optimization of
Surface Roughness in Face Turning Operation in Machining
of EN-8, International Journal of Engineering Science &
Advanced Technology, Volume-2, pp. 807 – 812, Jul-Aug
2012.
[8] Rodrigues L.L.R., Kantharaj A.N., Kantharaj B., Freitas W.
R. C. and Murthy B.R.N., ?Effect of Cutting Parameters on
Surface Roughness and Cutting Force in Turning Mild
Steel, Research Journal of Recent Sciences, Vol. 1, pp. 19-
26, October 2012.
[9] Nitin Sharma, Shahzad Ahmad, Zahid A. Khan and Arshad
Noor Siddiquee, ?Optimization of Cutting Parameters for
Surface Roughness in Turning, International Journal of
Advanced Research in Engineering and Technology, Volume
3, pp. 86 – 96, January- June 2012.
[10] H.M. Somashekara and N. Lakshmana Swamy, ?Optimizing
Surface Roughness in Turning Operation using Taguchi
Technique and ANOVA, International Journal of
Engineering Science and Technology, Vol. 4,pp. 1967 –
1973, May 2012.
[11] Upinder Kumar Yadav, Deepak Narang and Pankaj Sharma
Attri, ?Experimental Investigation And Optimization Of
Machining Parameters For Surface Roughness In CNC
Turning By Taguchi Method, International Journal of
Engineering Research and Applications, Vol. 2, pp. 2060 –
2065, July-August 2012.
[12] BalaRaju. J, Anup Kumar. J, Dayal Saran. P and C.S.
Krishna Prasad Rao, ?Application of Taguchi Technique for
Identifying Optimum Surface Roughness in CNC end
Milling Process, International Journal of Engineering
Trends and Technology, Volume 2, pp. 103 – 110, March
2015.
[13] Vishal Francis, Ravi. S. Singh, Nikita Singh, Ali. R. Rizvi
and Santosh Kumar, ?Application of Taguchi Method and
ANOVA in Optimization of Cutting Parameters for Material
Removal Rate and Surface Roughness in Turning
Operation, International Journal of Mechanical
Engineering and Technology, Volume 4, pp. 47-53, May -
June 2013.
[14] D.V.V. Krishan Prasad, ?Influence of Cutting Parameters on
Turning Process Using ANOVA Analysis, Research
Journal of Engineering Sciences, Vol. 2, pp. 1 – 6,
September 2013.
[15] M. M. Koura, T. H. Sayed and A. S. El-Akkad, ?Modeling
and Prediction of Surface Roughness, International Journal
of Engineering Research & Technology, Vol. 3, pp. 694-699,
July 2014.
[16] Brajesh Kumar Lodhi and Rahul Shukla, ?Experimental
Analysis on Turning parameters for Surface roughness and
MRR, Journal of Emerging Technologies and Innovative
Research, Volume 1, pp. 554 -557, Nov 2014.
[17] Rony Mohan, Josephkunju Paul C and George Mathew,
?Optimization of Surface Roughness of Bearing Steel during
CNC Hard Turning Process, International Journal of
Engineering Trends and Technology, Volume 17, pp. 173 –
175, Nov 14.
[18] Shunmugesh K., Panneerselvam K., Pramod M. and Amal
George, ?Optimization of CNC Turning Parameters with
Carbide Tool for Surface Roughness Analysis Using Taguchi
Analysis, Research Journal of Engineering Sciences, Vol.
3, pp. 1 – 7, June 2014.
[19] Sushil Kumar Sharma and Sandeep Kumar, ?Optimization of
Surface Roughness in CNC Turning of Mild Steel (1018)
using Taguchi method, International Journal of
Engineering Research & Technology, Vol. 3, pp. 2928 –
2932, January – 2014.
[20] Taquiuddin Quazi and Pratik gajanan more, ?Optimization of
Turning Parameters Such as Speed Rate, Feed Rate, Depth of
Cut for Surface Roughness by Taguchi Method, Asian
Journal of Engineering and Technology Innovation, Volume:
02 , pp. 5 – 24, March 2014.
[21] Bheem Singh Rajpoot, Dharma Ram Moond and Shrivastava,
Sharad, ?Investigating the Effect of Cutting Parameters on
Average Surface Roughness and Material Removal Rate
during Turning of Metal Matrix Composite Using Response
Surface Methodology, International Journal on Recent and
Innovation Trends in Computing and Communication,
Volume: 3, pp. 241 – 247, January 2015.
Keywords
Cutting parameters, Surface Roughness,
Turning.