Extraction and Optimization of Oil from Post Hospital Waste Plastic through Catalytic Pyrolysis using Central Composite Design (CCD)

Extraction and Optimization of Oil from Post Hospital Waste Plastic through Catalytic Pyrolysis using Central Composite Design (CCD)

  IJETT-book-cover           
  
© 2024 by IJETT Journal
Volume-72 Issue-5
Year of Publication : 2024
Author : S. Arul Selvan, K. Kumaravel
DOI : 10.14445/22315381/IJETT-V72I5P107

How to Cite?

S. Arul Selvan, K. Kumaravel, "Extraction and Optimization of Oil from Post Hospital Waste Plastic through Catalytic Pyrolysis using Central Composite Design (CCD)," International Journal of Engineering Trends and Technology, vol. 72, no. 5, pp. 58-65, 2024. Crossref, https://doi.org/10.14445/22315381/IJETT-V72I5P107

Abstract
In this study, waste plastic oil was extracted and optimized from Post-Hospital Waste Plastic (PHWP) through a catalytic pyrolysis process. The Central Composite Design (CCD) of Response Surface Methodology (RSM) through the Design-Expert software was used in this work to optimize the response by varying the input variables pyrolysis process. In this model, the reaction temperature from 300 to 500°C and retention time from 60 to 120 minutes are considered variable factors, and the yield of waste plastic oil is considered an independent response. The ANOVA of the CCD indicated that all the process-independent variables investigated had significant impacts on the sorption capacity of waste plastic oil obtained from PHWP. This work was split into two phases. In phase I, the retention time and reaction temperature were considered as factors, and waste plastic oil as a response. The obtained experimental data showed that the optimized 90-minute retention time and reaction temperature of 450°C resulted in an optimum yield of waste plastic oil. For the second phase of this work, the optimum retention time (90 min) is set as constant and reaction temperature with catalysts quantity as factors. Three catalysts (Zeolite, Alumina and Silica) with different ratios given by the model are used to increase the yield of waste plastic oil. From the CCD analysis, it is found that the catalysts effectively increase the yield of waste plastic oil.

Keywords
Waste Plastic Oil, Pyrolysis, Post-Commercial Waste Plastic, Post-Hospital Waste Plastic, Post-Domestic Waste Plastic.

References
[1] Guangcan Su et al., “Valorisation of Medical Waste through Pyrolysis for a Cleaner Environment: Progress and Challenges,” Environmental Pollution, vol. 279, pp. 1-13, 2021.
[CrossRef] [Google Scholar] [Publisher Link]
[2] Luis Alberto De la Flor-Barriga, and Ursula Fabiola Rodríguez-Zúñiga, “Numerical Analysis on a Catalytic Pyrolysis Reactor Design for Plastic Waste Upcycling Using CFD Modelling,” RSC Advances, no. 12, pp. 12436-12445, 2022.
[CrossRef] [Google Scholar] [Publisher Link]
[3] Uisung Lee, J.N. Chung, and Herbert A. Ingley, “High-Temperature Steam Gasification of Municipal Solid Waste, Rubber, Plastic and Wood,” Energy and Fuels, vol. 28, no. 7, pp. 4573-4587, 2014.
[CrossRef] [Google Scholar] [Publisher Link]
[4] Rohit Kumar Singh et al., “Impact of Fast and Slow Pyrolysis on the Degradation of Mixed Plastic Waste: Product Yield Analysis and their Characterization,” Journal of the Energy Institute, vol. 92, no. 6, pp. 1647-1657, 2019.
[CrossRef] [Google Scholar] [Publisher Link]
[5] M. Mani, C. Subash, and G. Nagarajan, “Performance, Emission and Combustion Characteristics of a DI Diesel Engine Using Waste Plastic Oil,” Applied Thermal Engineering, vol. 29, no. 13, pp. 2738-2744, 2009.
[CrossRef] [Google Scholar] [Publisher Link]
[6] Ioannis Kalargaris, Guohong Tian, and Sai Gu, “Combustion, Performance and Emission Analysis of a DI Diesel Engine Using Plastic Pyrolysis Oil,” Fuel Processing Technology, vol. 157, pp. 108-115, 2017.
[CrossRef] [Google Scholar] [Publisher Link]
[7] Mateo Cordier et al., “Plastic Pollution and Economic Growth: The Influence of Corruption and Lack of Education,” Ecological Economics, vol. 182, pp. 1-13, 2021.
[CrossRef] [Google Scholar] [Publisher Link]
[8] Ceyla Güngör et al., “Engine Performance and Emission Characteristics of Plastic Oil Produced from Waste Polyethylene and its Blends with Diesel Fuel,” International Journal of Green Energy, vol. 12, no. 1, pp. 98-105, 2015.
[CrossRef] [Google Scholar] [Publisher Link]
[9] Hariram Venkatesan et al., “Experimental Study on Combustion and Performance Characteristics in a DI CI Engine Fuelled with Blends of Waste Plastic Oil,” Alexandria Engineering Journal, vol. 57, no. 4, pp. 2257-2263, 2018.
[CrossRef] [Google Scholar] [Publisher Link]
[10] V.L. Mangesh et al., “Combustion and Emission Analysis of Hydrogenated Waste Polypropylene Pyrolysis Oil Blended with Diesel,” Journal of Hazardous Materials, vol. 386, 2020.
[CrossRef] [Google Scholar] [Publisher Link]
[11] Amar Kumar Das et al., “Energy, Exergy and Emission Analysis on a DI Single Cylinder Diesel Engine Using Pyrolytic Waste Plastic Oil Diesel Blend,” Journal of the Energy Institute, vol. 93, no. 4, pp. 1624-1633, 2020.
[CrossRef] [Google Scholar] [Publisher Link]
[12] Sudershan B. Gadwal et al., “Performance and Emission Characteristic Studies on CRDI Diesel Engine Fuelled with Plastic Pyrolysis Oil Blended with Ethanol and Diesel,” International Journal of Sustainable Engineering, vol. 12, no. 4, pp. 262-271, 2018.
[CrossRef] [Google Scholar] [Publisher Link]
[13] Maridu Bhargavi et al., “Effective Utilization and Optimization of Waste Plastic Oil with Ethanol Additive in Diesel Engine Using Full Factorial Design,” Materials Today: Proceedings, vol. 52, pp. 930–936, 2022.
[CrossRef] [Google Scholar] [Publisher Link]
[14] Khatha Wathakit et al., “Characterization and Impact of Waste Plastic Oil in a Variable Compression Ratio Diesel Engine,” Energies, vol. 14, no. 8, pp. 1-18, 2021.
[CrossRef] [Google Scholar] [Publisher Link]
[15] C. Syed Aalam, and C.G. Saravanan, “Effects of Fuel Injection Pressure on CRDI Diesel Engine Performance and Emissions Using CCD,” International Research Journal of Engineering and Technology, vol. 2, no. 5, pp. 1411-1416, 2015.
[Google Scholar] [Publisher Link]
[16] Natthawat Thonglhueng et al., “Optimization of Iodine Number of Carbon Black Obtained from Waste Tire Pyrolysis Plant via Response Surface Methodology,” Heliyons, vol. 8, no. 12, pp. 1-10, 2022.
[CrossRef] [Google Scholar] [Publisher Link]
[17] Jonghun Lim et al., “Optimal Strategy to Sort Plastic Waste Considering Economic Feasibility to Increase Recycling Efficiency,” Process Safety and Environmental Protection, vol. 165, pp. 420-430, 2022.
[CrossRef] [Google Scholar] [Publisher Link]
[18] C. Syed Aalam, and C.G. Saravanan, “Effects of Nano Metal Oxide Blended Mahua Biodiesel on CRDI Diesel Engine,” Ain Shams Engineering Journal, vol. 8, no. 4, pp. 689-696, 2017.
[CrossRef] [Google Scholar] [Publisher Link]
[19] C. Syed Aalam, C.G. Saravanan, and M. Kannan, “Experimental Investigations on a CRDI System Assisted Diesel Engine Fuelled with Aluminium Oxide Nanoparticles Blended Biodiesel,” Alexandria Engineering Journal, vol. 54, no. 3, pp. 351-358, 2015.
[CrossRef] [Google Scholar] [Publisher Link]
[20] C. Syed Aalam, C.G. Saravanan, and B. Prem Anand, “Impact of High Fuel Injection Pressure on the Characteristics of CRDI Diesel Engine Powered by Mahua Methyl Ester Blend,” Applied Thermal Engineering, vol. 106, pp. 702-711, 2016.
[CrossRef] [Google Scholar] [Publisher Link]