Effect of Channel Orientation on Heat Transfer in Rotating Rectangular Channel (AR=4) with 90º Rib Turbulators
International Journal of Engineering Trends and Technology (IJETT) | |
|
© 2016 by IJETT Journal | ||
Volume-32 Number-3 |
||
Year of Publication : 2016 | ||
Authors : Jalal M. Jalil, Fouad A. Saleh, and Sa'ib A. Hamid Al-Jubury |
||
DOI : 10.14445/22315381/IJETT-V32P222 |
Citation
Jalal M. Jalil, Fouad A. Saleh, Sa'ib A. Hamid Al-Jubury"Effect of Channel Orientation on Heat Transfer in Rotating Rectangular Channel (AR=4) with 90º Rib Turbulators", International Journal of Engineering Trends and Technology (IJETT), V32(3),124-128 February 2016. ISSN:2231-5381. www.ijettjournal.org. published by seventh sense research group
Abstract
An experimental investigation to determine the effect of the channel orientation on heat transfer enhancement in stationary and rotating rectangular channel of constant aspect ratio (AR=4) with facing 90º rib turbulators. A Reynolds number range tested in this study was 8000-13500. The effect of channel orientations of β=90 deg and 135 deg with respect to the plane of rotation is investigated and the rotation effect is also studied, where the rotational velocity is fixed at 500 rpm. The results show that the higher heat transfer enhancement for channel at 135º by 2.7 to 2.2 times while was 2.5 to 2 times for β=90º for stationary case. But for rotational cases the heat transfer enhancement was 3.4 to 2.6 and 2.8 to 2.3 for β=135º and β=90º, respectively for Reynolds number range 8000 to 13500, comparing with smooth non rotating pipe adopted by Dittus-Boelter/McAdams. Also the results show that the average percentage of heat transfer enhancement of duct at β=135º was 3% higher than duct at β=90º for stationary case while for rotating case was 12% for the range of Reynolds number tested in this work.
References
[1] W.-L. Fu, "Aspect Ratio Effect on Heat Transfer in Rotating Two-Pass Rectangular Channels with Smooth Walls and Ribbed Walls", Ph.D. Thesis, Texas A&M University, (2005).
[2] B.V. Johnson, J.H. Wagner, G.D. Steuber, and F.C. Yeh, '' Heat Transfer in Rotating Serpentine Passages with Trips Skewed to the Flow", ASME Paper 92-GT-191, June 1992.
[3] B.V. Johnson, J.H. Wagner, G.D. Steuber, and F.C. Yeh, '' Heat Transfer in Rotating Serpentine Passages with Selected Model Orientation for Smooth or Skewed Trip Walls", NASA Technical Memorandum 106126, may 1993.
[4] J. A. Parsons, J.C. Han, and Y. Zhang, " Effect of Model Orientation and Wall Heating Condition on Local Heat Transfer in a Rotating Two-Pass Square Channel with Rib Turbulators", Int. J. Hear Mass Transfer. Vol. 38, No. 7, pp. 1151-1159, 1995.
[5] S. Dutta, and J. C. Han, "Local Heat Transfer in Rotating Smooth and Ribbed Two-Pass Square Channel with Three Channel Orientation", ASME Journal of heat transfer Vol. 118, pp. 578-584, 1996.
[6] T. S. Griffith, L. Al-Hadhrami, and J. C. Han, " Heat Transfer in Rotating Rectangular Cooling Channels (AR=4) with Angled Ribs", Journal of Heat Transfer, Vol. 124 August 2002 617-625.
[7] L. Al-Hadhrami, and J.C. Han, " Effect of Rotation on Heat Transfer in Two-Pass Square Channels with Five Different Orientations of 45º Angled Rib Turbulators", International Journal of Heat and Mass Transfer 46 (2003) 653–669.
[8] L. Al-Hadhrami, T. Griffith, and J.C. Han, " Heat Transfer in Two-Pass Rotating Rectangular Channels (AR=2) With Five Different Orientations of 45 Deg V-Shaped Rib Turbulators ", Journal of Heat Transfer, Vol. 125 April 2003 232-242.
[9] P. Agarwal," Heat/Mass Transfer in Smooth and Ribbed Rectangular Serpentine Passages of Different Aspect Ratio's and Orientation", MSc. Thesis, Graduate Faculty of the Louisiana State University and Agricultural and Mechanical College, May, (2004).
[10] T.M. Liou, S.W. Chang, J.H. Hung, S.F. Chiou, "High Rotation Number Heat Transfer of a 45◦ Rib- Roughened Rectangular Duct with Two Channel Orientations", International Journal of Heat and Mass Transfer 50 (2007) 4063–4078.
[11] British-Standard 1042: Section 1.1: (1981). [12] J. C. Han, Y. M. Zhang, C. P. Lee, "Augmented Heat Transfer in Square Channels With Parallel, Crossed, and V-Shaped Angled Ribs", ASME Journal of Heat Transfer, 113, (1991), 590-596.
[13] J. S. Park, J. C. Han, Y. Huang, S. Ou, R. J. Boyle, "Heat Transfer Performance Comparisons of Five Different Rectangular Channels with Parallel Angled Ribs", Int. J. Heat Mass Transfer, 35, No. 11, (1992), 2891- 2903.
[14] J. C. Han and Y. M. Zhang, "High Performance Heat Transfer Ducts with Parallel Broken and V-Shaped Broken Ribs", Int. J. Heat Mass Transfer, 35, No. 2, (1992), 513-523.
Keywords
Enhancement, Heat transfer, Rotating, channel orientation, Turbines cooling.