IJBTT

Development of an Automatic Device for Maintaining Normal Air Pressure in Pneumatic Tires

Development of an Automatic Device for Maintaining Normal Air Pressure in Pneumatic Tires
	© 2023 by IJETT Journal
	Volume-71 Issue-2
	Year of Publication : 2023
	Author : M.S. Dmitriyev, V.V. Rudnev, M.L. Khasanova, E.P. Merkulov, I.A. Polunin
	DOI : 10.14445/22315381/IJETT-V71I2P213

How to Cite?

M.S. Dmitriyev, V.V. Rudnev, M.L. Khasanova, E.P. Merkulov, I.A. Polunin, "Development of an Automatic Device for Maintaining Normal Air Pressure in Pneumatic Tires," International Journal of Engineering Trends and Technology, vol. 71, no. 2, pp. 104-110, 2023. Crossref, https://doi.org/10.14445/22315381/IJETT-V71I2P213

Abstract
The purpose of the article is to solve the problem of increasing the life of pneumatic tires, reducing fuel consumption and improving road safety. It is known that most pneumatic tires fail prematurely due to the fact that the pressure in the tires is violated; at the same time, overheating, swelling of cracks, etc., occur. Often, wheeled vehicles operate with a deviation from the recommended standards. During the hot season, when high-speed vehicles move on a hard rough road, the tire pressure rises due to heated air. There is an increase in the specific pressure at the point of contact between the tire and the road, which leads to a deterioration in braking dynamics. Depending on the low or high air pressure in pneumatic tires, the dynamic and economic qualities of cars are reduced. This leads to an increase in the cost of transportation and the likelihood of traffic accidents. As a solution to this problem, the authors proposed an automatic device for maintaining normal air pressure in the tires using compressed nitrogen. The proposed device includes a high-pressure cylinder, filling valve, high-pressure reducer and locking device. High-pressure cylinders can be mass-produced by manufacturers for various vehicles. They can be structurally made in the cavity of the wheel disk. Refilling of these cylinders can be carried out at special gas stations, tire shops or service centers.

Keywords
Compressed nitrogen, Fuel consumption, High pressure reducer, Pneumatic tires, Tire pressure.

References
[1] Rosan Ivanov, “Tire Wear Modeling,” Transport Problems, vol. 11, no. 3, pp. 111-120, 2016. Crossref, http://dx.doi.org/10.20858/tp.2016.11.3.11
[2] V. Orekhov, “Analysis of Operating Conditions of Urban Bus Tires,” Sciences of Europe, vol. 83, no. 1, pp. 36-41, 2021. Crossref, https://doi.org/10.24412/3162-2364-2021-83-1-36-41
[3] V. P. Boikov, V. V. Guskov, and A. S. Pavarekha, “Automated Tire Pressure Control System for Multi-purpose Wheeled Vehicles,” Science and Technique, vol. 20, no. 1, pp. 33-36, 2021. Crossref, http://dx.doi.org/10.21122/2227-1031-2021-20-1-33-36
[4] V. V. Rudnev et al., “Pneumatic Hybrid Power Plants Efficiency,” International Journal of Engineering and Advanced Technology, vol. 8, no. 6, pp. 5186-5191, 2019. Crossref, http://www.doi.org/10.35940/ijeat.B5552.088619
[5] V. Orekhov, “Prototype of Equipment for Express Tire Pressure Control,” Znanstvena Misel, no. 60, no. 1, pp. 34-41, 2021.
[6] Rui He et al., “Laboratory Experimental Study of Tire Tractive Performance on Soft Soil: Towing Mode, Traction Mode, and Multi-pass Effect,” Journal of Terramechanics, vol. 95, pp. 33-58, 2021. Crossref, https://doi.org/10.1016/j.jterra.2021.02.001
[7] Jakub Polasik, Konrad J. Waluś, and Łukasz Warguła, “Experimental Studies of the Size Contact Area of a Summer Tire as a Function of Pressure and The Load,” Procedia Engineering, vol. 177, pp. 347-351, 2017. Crossref, https://doi.org/10.1016/j.proeng.2017.02.203
[8] R. L. Raper et al., “The Effects of Reduced Inflation Pressure on Soil-tire Interface Stresses and Soil Strength,” Journal of Terramechanics, vol. 32, no. 1, pp. 43-51, 1995. Crossref, https://doi.org/10.1016/0022-4898(95)00002-I
[9] Hongyun Wu et al., “Research on the Effect of Grounding Pressure Distribution on Traction Force of Tracked Vehicle,” Proceedings of the 20-th International Offshore and Polar Engineering Conference, ISOPE-2010, Beijing, China, pp. 197-200, 2010.
[10] M. L. Khasanova et al., “Reducing the Nitrogen Oxides Content in the Internal Combustion Engine Exhaust Gases by Using the Waste Heat Engine,” International Journal of Emerging Trends in Engineering Research, vol. 8, no. 8, pp. 4537-4543, 2020. Crossref, https://doi.org/10.30534/ijeter/2020/80882020
[11] M. S. Dmitriyev, M. L. Khasanova, and A. V. Raznoshinskaya, “Substantiation of Hydraulic System for Weighing Freights Transported with Dump Trucks,” Procedia Engineering, vol. 206, pp. 1604-1610, 2017. Crossref, https://doi.org/10.1016/j.proeng.2017.10.685
[12] A. Cudzik et al., “Traction Properties of the Wheel-turfy Soil System,” International Agrophysics, vol. 24, no. 4, pp. 343-350, 2010.
[13] Jiahong Zhang et al., “Development of MEMS Composite Sensor with Temperature Compensation for Tire Pressure Monitoring System,” Journal of Micromechanics and Microengineering, vol. 31, p. 125015, 2021. Crossref, https://doi.org/10.1088/1361-6439/ac349d
[14] M. S. Dmitriyev et al., “Development of an Automatic Differential Lock Based on the Tangential Inertial Forces Principle,” International Journal of Engineering Trends and Technology, vol. 69, no. 10, pp. 7-14, 2021. Crossref, https://ijettjournal.org/archive/ijett-v69i10p202
[15] Michal Janulin, “Method of Indicating Effective Circumferences of Rolling Vehicle Wheels,” Diagnostyka, vol. 21, no. 4, pp. 95-101, 2020. Crossref, https://doi.org/10.29354/diag/130614
[16] Dongdong Hou et al., “ID Calibration Device Design for Vehicle Tire Pressure Monitoring System Based on Bluetooth Communication,” Procedia Computer Science, vol. 202, pp. 223-227, 2022. Crossref, https://doi.org/10.1016/j.procs.2022.04.030
[17] Juyong Kang, “Robust Estimation Method of Tire Torsional Resonance Frequency to Detect Decrease in Tire Inflation Pressure,” Vehicle System Dynamics, vol. 60, no. 7, pp. 2358-2374, 2022. Crossref, https://doi.org/10.1080/00423114.2021.1906920
[18] Yang Yang et al., “External Digital Tire Pressure Monitoring System Based on MEMS Pressure Sensor,” Chinese Journal of Sensors and Actuators, vol. 23, no. 9, pp. 1347-1352, 2010. Crossref, http://dx.doi.org/10.3969/j.issn.1004-1699.2010.09.027
[19] Z. Han et al., “New Method for Monitoring Tire Pressure of Cars Based on the Tire Radial Deformation,” Chinese Journal of Mechanical Engineering (English Edition), vol. 23, no. 2, pp. 180-184, 2010.
[20] Mark Vaszary et al., “Securing Tire Pressure Monitoring System for Vehicular Privacy,” 2021 IEEE 18th Annual Consumer Communications & Networking Conference (CCNC), pp. 1-6, 2021. Crossref, https://doi.org/10.1109/CCNC49032.2021.9369576
[21] Kouichi Tanoshita, Koji Nakatani, and Yoshihide Yamada, “Electric Field Simulation Around a Car of the Tire Pressure Monitoring System,” IEICE Transactions on Communication, vol. E90-B, no. 9, pp. 2416-2422, 2007. Crossref, https://doi.org/10.1093/ietcom/e90- b.9.2416
[22] Paul Manuel, Nandalal, and P,P.S.Amal, “Autonomous Tyre Pressure Maintenance System,” SSRG International Journal of Mechanical Engineering, vol. 5, no. 3, pp. 1-5, 2018. Crossref, https://doi.org/10.14445/23488360/IJME-V5I3P101
[23] J. J. Mahakud, and Priyabrata Pattanaik, “Design of an Automatic Tire Pressure Maintenance System for Automobiles,” International Journal of Psychosocial Rehabilitation, vol. 23, no. 5, pp. 267-273, 2019. Crossref, https://doi.org/10.37200/V23I5/17291
[24] Y. G. Gorshkov, M. S. Dmitriyev, and D. V. Potiomkina, “Improvement of Working Conditions and Increase of Safety of Agricultural Purpose Cars Drivers,” Labor protection and safety measures in agriculture, no. 9, pp. 17–20, 2006.
[25] Moataz Ahmed, Haoxiang Lang, and Moustafa El-Gindy, “Vehicles' Directional Stability Control: Literature Survey,” International Journal of Vehicle Systems Modelling and Testing, vol. 15, no. 4, pp. 244-273, 2021. Crossref, https://doi.org/10.1504/IJVSMT.2021.122819
[26] R.M. Van Auken, and S.A. Kebschull, “Lateral-directional Stability and Manual Control of Understeering and Oversteering Vehicles in Off-road Conditions Based on a 2-d of Cornering Compliance Vehicle Dynamics Model,” ASME International Mechanical Engineering Congress and Exposition, 2021. Crossref, https://doi.org/10.1115/IMECE2021-71854