Evaluation of Mechanical Properties of Magnesium Reinforced with Titanium Oxide Composites

  IJETT-book-cover  International Journal of Engineering Trends and Technology (IJETT)          
  
© 2016 by IJETT Journal
Volume-42 Number-8
Year of Publication : 2016
Authors : Lakshmanan Pillai.A, Jinu.G.R, Elansezhian.R
DOI :  10.14445/22315381/IJETT-V42P280

Citation 

Lakshmanan Pillai.A, Jinu.G.R, Elansezhian.R "Evaluation of Mechanical Properties of Magnesium Reinforced with Titanium Oxide Composites", International Journal of Engineering Trends and Technology (IJETT), V42(8),466-471 December 2016. ISSN:2231-5381. www.ijettjournal.org. published by seventh sense research group

Abstract
The experimental investigations of magnesium based matrix material reinforced with the TiO2 particles with various weight ratios of 2.5, 5, 7.5 and 10% are presented in this research paper. The purpose of this work is to intricate the manufacturing processes of pure magnesium with the addition of Titanium oxide through the powder metallurgy route. The powder blending was done with the energetic ball and jar mill. The compaction pressure of 650Mpa is given to improve the process of cold compaction and strength. The Sintering temperature of 550 oC and holding time of 40 min was used to sinter the compacts to get better results. The microstructural analysis by scanning electron microscopy (SEM) for the starting powders and fabricated samples are carried out and results revealed that homogeneous composition is present. The mechanical properties are evaluated and the results proved that improvement in 13.8%, 17.8% and 29% for the density, hardness values and ultimate tensile strength.

 References

[1] David E Alman, Properties of Metal Matrix Composites, ASM Hand Book, 2nd edition, 2001.
[2] T.W Clyne, “An Introductory overview of MMC systems, types and Developments, Comprehensive Composite Materials”, Reference Module in Materials Science and Materials Engineering , Vol.3 ,pp. 1-26, 2000.
[3] Chawla Nikilesh and Chawla Krishan , Metal Matrix Composites, ISBN 978-0-387-28567-2, 2006.
[4] M. Lei and H. Ledbetter, “Communications: elastic constants of SiCp/Al: measurements and modeling ”, Metall. Mater. Trans., Vol.25A, pp 2832-2835.1994.
[5] Amresh Kumar and Manoj Kumar , “Mechanical behavior of Particle Reinforced Aluminium Matrix Composites”, IJIRST, Vol. 2 (12), pp. 436-439,2016.
[6] A.W?odarczyk-Fligier, L.A Dobrza?ski , M .Kremzer and M.Adamiak, “ Manufacturing of aluminium matrix composite materials reinforced by Al2O3 particles” , Journal of Achievements in Materials and Manufacturing Engineering ,Vol. 27 (1) , pp. 99-102, 2008.
[7] L.A. DobrzaEski ,M. Kremzer, A.J. Nowak and A. Nagel, “Composite materials based on porous ceramic perform infiltrated by aluminium alloy”, Journal of Achievements in Materials and Manufacturing Engineering, Vol.20 , pp. 95-98. 2007.
[8] M.K. Khan, “ Application of Powder Metallurgy”, Int. J. Of Powder Metallurgy and Powder Tech.,Vol.16(2) , pp. 121-130, 2007.
[9] David T Gethin, Viet D Tran, Roland W Lewis and Ahmad K Ariffin, “Investigation of powder compaction processes”, Int. J.Of Powder Metallurgy, Vol.30 (4), pp. 385-398, 1994.
[10] Scubert T et al, “Interfacial characterization of Cu/diamond composites prepared by powder metallurgy for heat sink applications”, Scripta Materialia , Vol.58 (4), pp. 23-266,2008.
[11] Y.L.Xi , D.L. Chai, W.X. Zhang and J.E. Zhou , “ Ti–6Al–4V particle reinforced magnesium matrix composite by powder metallurgy”, Material Letters, Vol.59 (14-15), pp. 1831-1835, 2005.
[12] P.Ashwath and M. Anthony Xavior, “The Effect of Ball Milling & Reinforcement Percentage on Sintered Samples of Aluminium Alloy Metal Matrix Composites”, Procedia Engineering , (97), pp. 1027 – 1032, 2014.
[13] Goldstein, N.Travitzky , A. Singurindi, and M. Kravchik , “ Effects of microwave sintering processing parameters”, Journal of the European Ceramic Society Vol.12, pp. 2067–2072, 1999.
[14] Van Tich Nguyen, Dinh Phuong Doan, Tran BaoTrung Tran, Van Duong Luong, Van An Nguyen and Anh Tu Phan, “Microstructural evolution and some mechanical properties of nanosized yttrium oxide dispersion strengthened 13Cr steel”, Adv. Nat. Sci.: Nanosci. Nanotechnol,pp.1-4, 2010.
[15] Sanjay Kumar Thaku, K.Balasubramanian and Manoj Gupta, “ Microwave Synthesis and Characterization of Magnesium based Composites containing Nanosized SiC and Hybrid Reinforcements”, Transactions of ASME – J. of Engg. Materials and Tech. , Vol. 129 , pp. 194-199, 2007.
[16] Q.C.Jiang, H.Y.Wang ,B.X. Ma, Y.Wang , and F. Zhao , “Fabrication of B4C particulate reinforced magnesium matrix composite by powder metallurgy”, Journal of Alloys and Compounds, Vol. 386 (1-2),pp. 177-181, 2005.
[17] Q.C.Jiang, H.Y.Wang ,B.X. Ma, Y.Wang , and F. Zhao, “Fabrication of TiB2 particulate reinforced magnesium matrix composites by powder metallurgy”, Materials Letters , Vol.58( 27-28), pp. 3509-3513, 2004.
[18] L.A.Dobrza?ski ,A. W?odarczyk and A. Adamiak , “Composite materials based on EN AW-Al Cu4Mg1(A) aluminum alloy reinforced with the Ti(C,N) ceramic particles”, Material Science Forum, pp. 243-248, 2006.
[19] M. Adamiak, J.B. Fogagnolo, E.M. Ruiz-Navas, L.A. Dobrza?ski and J.M. Torallba , “ Structure and properties of composite materials obtained by mechanical milling and hot extrusion”,Journal of Materials Processing Technology, pp. 155 -156, 2004.

Keywords
—SDH, Carbohydrates, Common carp, Cold stress, Seasons, Non-Osmatic tissues, Osmatic tissues.